A kitchen sink drain fails for three reasons, and only one of them is the drain itself. The basket strainer in the bowl decides what gets through, the trap under the cabinet decides whether sewer gas comes back, and whatever sits downstream decides whether fat and starch set into a plug you cannot reach. Buyers who order a "drain for kitchen sink" as a single line item usually receive a strainer that fits the hole and nothing else, then spend the season explaining callbacks.
This is written for importers and distributors specifying sink drainage for hotels, canteens and rental projects: what the assembly is, what to check on a sample, and where the grease problem is really solved.
Four parts, sold as one item and blamed as one item.
Every joint is a leak path. Most bad-drain leaks are a missing gasket at the flange, a tailpiece cut too short, or a slip nut tightened at the top only.
The basket is a filter, so its perforation pattern matters more than its polish. Fine perforations hold coffee grounds and rice but slow the flow. Coarse perforations drain fast and pass solids into the trap. A hotel or canteen wants the coarse end, a cafe with heavy grounds wants the fine end plus a mesh insert. Ask for both baskets and test them.
Then check five points.
A strainer is a small part. A bad one generates a service call that costs more than the container.
Fat does not disappear when it leaves the sink. It cools in the pipe, sticks to the wall, catches starch and hair, and builds a layer that narrows the bore. Detergent does not remove it. It emulsifies a thin film and lets the rest set again.
The mistake is to answer this with a bigger basket. The real answers sit downstream:
The same logic applies to the gully taking overflow and mop water. A BQ20157-Q brass floor drain with a removable strainer basket is what we build for commercial wet areas, because the basket is the part that gets cleaned and it should come out without a fight. For kitchens running stainless benches and stainless sinks, the BQ-105 American stainless steel floor drain keeps the material story consistent across the room.
A drain that smells has lost its water seal, or never had one.
Under a sink the seal lives in the trap. Two things break it: evaporation in a sink nobody uses, and siphonage when the waste discharges into a stack with no vent. A fixture used daily solves the first. An air admittance valve or a proper vent branch solves the second, and no strainer design will fix a siphoning trap.
Floor gullies are a separate case. EN 1253-1 asks for a 50 mm water seal on gullies, and that depth exists for exactly this reason. A shallow gully in a kitchen corner that never sees water is the most common source of drain smell complaints we hear about. Where the specification allows, choose a gully with a deep seal and a removable core, and put it where it actually gets water.
Brass and 304 stainless cover most kitchen drainage. Brass takes plating and colour matching, which matters when the sink drain sits next to a brass faucet on the same counter. Stainless resists the chloride cleaners used on food contact surfaces.
Finish names travel badly. Chrome, brushed nickel, antique brass and black each mean something slightly different to a plater in one province and to a buyer in another. Send a physical chip, not a word. On our floor drain range the same body is offered in chrome, brushed nickel, antique brass, rose gold, titanium and black, and buyers who approve a chip rather than a name get far fewer rejections at goods-in.
One finish carried across the drain and the faucet keeps a single visual language in the space, which is what hotel projects audit on handover.
Most problems in this category start with mixing suppliers. The strainer comes from one trader, the trap from another, the floor gully from a third, and nobody owns the joint between them.
Ask one supplier for the strainer, tailpiece, trap, floor gully and faucet together, with a sample of each. Then check four things on arrival.
| Check | What to do | Why it fails |
|---|---|---|
| Thread match | Fit the tailpiece into the trap by hand | BSP against NPS leaks at the slip nut |
| Basket fit | Drop the basket in and lift it out wet | Tolerances too tight jam with food debris |
| Seal depth | Measure the trap and the gully core | A shallow seal dries and passes gas |
| Finish match | Compare against the approved chip in daylight | Metallic finishes shift under shop lighting |
Then fit one complete set on a sink in your own warehouse before the container is released. It takes an afternoon and it is the only test that catches a mixed thread order.
We manufacture brass and stainless steel floor drains, brass basin and pull out faucets, angle valves, bibcocks, shower heads and bidet sprayers in Yuhuan, and export them under buyer brands with ODM and OEM service. Basket strainers and grease interceptors we supply and source alongside the drainage range.
Send us the sink gauge, the finish chip, and the fixture schedule for the kitchen, and we will come back with the matching drain, gully and faucet set plus a sample of each for your own fit test.