logo
News Details
Home / News /

Company news about When Half the Holes Stop Spraying: Cleaning a Scaled Shower Head

When Half the Holes Stop Spraying: Cleaning a Scaled Shower Head

2026-11-16

A shower head that still runs but sprays from only half its holes is almost always blocked by scale on the spray face, not worn out. The fix takes about half an hour and no special tools: unscrew the head from the arm, soak the face in warm citric acid or distilled vinegar solution, brush the orifices, clear the stubborn ones with a wooden toothpick, then flush and refit. If the spray is weak everywhere rather than patchy, the blockage is upstream — inlet screen, flow restrictor insert or hose — and soaking the face will change nothing. Make that distinction before you fill a bowl.

Why the outer holes die first

Scale is calcium carbonate, the mineral hard water leaves behind when it evaporates. In a shower that happens between uses, not during them: after the valve closes a film of water stays on the face plate, and the last of it hangs at the rim, in the lowest point of a tilted face and around any orifice lip proud of the surface. Those spots dry last and stay damp longest, so they collect a ring of mineral the middle of the face never sees.

Size does the rest. Flow through a narrow passage falls steeply as the bore narrows, so a hole that has lost a fraction of its diameter loses far more than that fraction of its output. In practice the ring does not fade — it stops. The centre jets, carrying the highest velocity and self-flushing on every shower, stay clear. Hence the odd failure: a ring of dead holes around a working core, or one side spraying while the other weeps.

Heat accelerates it. Calcium carbonate is less soluble in hot water than in cold, so a head fed by a heater deposits mineral faster than a cold tap on the same supply, and can crust inside a season while the basin tap beside it stays clean.

Diagnose in two minutes: face, inlet, or hose

Unscrew the head, holding the arm so the pipe does not turn in the wall, then run the valve with only the hose attached, end pointed into a bucket. A full, steady stream means the restriction is in the head; a weak one means the problem is upstream — clogged inlet screen, scaled non-return valve, collapsed hose liner or debris from recent pipe work.

With the head in your hand, look straight at the face. Blockages arranged in a ring, a crescent or a single arc are scale on the orifices. A face that is weak on every hole, or that sprays at an angle, points elsewhere: a flow restrictor packed with grit, a mesh washer scaled solid, or a swivel ball joint no longer passing water properly. Shake the head — grit rattling inside is pipe debris, and it will keep blocking orifices until the line is flushed.

The soak that actually works

Use a shallow plastic container rather than a bag tied over the head, because a bag clings to the plating and holds acid against the seams. Warm water with citric acid, or white vinegar cut with an equal part of water, is enough: the solution does not need to be strong, only in contact with the blocked orifices. Stand the head face down so only the spray face is submerged; a plastic head can sit deeper, but keep the liquid below the threaded inlet of a plated brass body so the acid never reaches the joint where the plating ends.

Fifteen to thirty minutes lifts an ordinary film. For heavy crust, repeat the soak after brushing rather than leaving the head in overnight: acid left to evaporate concentrates, creeps under the edge of the plating and dulls the finish long before it dissolves the last of the scale. Lift the head out, rinse and brush the face under running water, and flush before refitting. Never use a scouring pad or wire brush on a plated face; the scratches hold scale better than the original surface did.

What acid leaves behind

Acid dissolves the soft outer layer, then stops at the plug grown into the throat of an orifice — thick, and shielded from fresh solution. Work along the dead holes with a wooden toothpick or stiff nylon bristle, twisting gently at each mouth; a steel needle clears faster but scratches the bore and leaves a rougher surface for the next layer. Then backflush: hold the head inlet uppermost, run water into the threaded opening and tap the face against your palm so loosened flakes leave through the holes instead of being pushed deeper.

Rubber or silicone nozzles need only a thumb rubbed across them while the head is wet; the scale cracks off the flexible tip in flakes.

The part the cleaning misses

Three components hide behind a spray face and are routinely blamed on scale. The inlet screen is a fine mesh washer; when it scales over, the whole face goes weak at once. The flow restrictor is a small insert in the inlet, sometimes a coloured disc with a pinhole, and scale in that pinhole throttles the entire head. The swivel ball joint carries a narrow passage and an O-ring; scale there makes the head stiff to angle and quietly cuts flow. All three are serviceable without replacing the head.

Brass faces and drilled orifices

A machined brass face with drilled orifices behaves differently from a moulded plastic one. The metal holds heat, and scale bonds to the cut edge of each hole rather than to a slick surface. It takes a proper soak and a pick rather than a thumb rub, but tolerates both without damage and does not craze or crack the way an aged plastic plate does. Where the head is being replaced anyway, solid brass is the more durable choice in hard water, because thin plated zinc fails by pitting and blistering — a finish problem no amount of descaling reverses.

For projects specifying a fixed wall-mounted head, the HS-001 brass shower head is built in solid brass on a wall-mount arm, in brushed nickel, chrome, antique brass, rose gold, titanium and black. Where the shower needs a handheld on a bracket instead, the SP-01 brass handheld shower head uses the same brass body and finish range. Both are made in our own workshop, so the face plate geometry and inlet screen are settled at the tooling stage.

Keeping the face clear

Scale returns wherever water is allowed to dry on the face, so the cheapest maintenance is drainage. Angle the head down after use so the last water runs off the rim, leave the enclosure door open or run the extractor, and wipe the face with a thumb once a week while the film is still soft. If your water leaves white rings on glass or taps within a week, treat descaling as monthly rather than annual. And after any plumbing work, flush the line with the head removed before refitting it, or debris will simply block the orifices you just cleared.

Repair or replace

Cleaning stops working when the damage is no longer mineral. Replace the head if the plating is blistered or lifting, the swivel ball has seized, the arm thread is stripped, the face plate is cracked around an orifice, or clearing a hole simply makes the jet spurt sideways. Replace the hose if the outer braid has bulged; the liner is failing. Everything else — screen, restrictor, washer, O-ring — is a part, not a head.

Next step

Tell us two things and we will tell you which head fits: whether your water leaves rings on glass within a week, and whether the shower runs a fixed wall-mounted head or a handheld on a bracket. Add the finish you are matching and we will send the closest sample set, together with the face plate drawing, so the spray pattern and the arm thread can be checked before anything is specified. Use the quote form on any product page to start.